How To Repair Dent In Drywall

Download Commodity

Download Article

Drywall is pretty tough, just an accidental elbow or a doorknob slam can create dents in it that are hard to ignore. Fortunately, fixing a dent in your wall isn't tough, and yous tin DIY information technology with but a few tools and an hour of labor. Continue reading to learn how you can patch a small dent that's less than ¹⁄₂  in (1.3 cm) wide or a large paring that's more than than ¹⁄₂  in (i.3 cm) wide all on your own.

Things Y'all Should Know

• Fix small wall dents with drywall mud and a plaster grid.
• For large dents, apply a drywall patch kit.
• Use 100-dust sandpaper to smooth the repair earlier painting over it.

1. one

   Shine on drywall mud with a putty knife. ^[1] Pick upward a tub of drywall mud and grab a putty knife from the hardware shop. Scoop upwardly a modest glob of drywall mud, and then employ your putty knife to spread information technology over the paring. You don't need a ton of drywall mud—simply add a thin layer to cover the dent completely.^[2]

   • This method works best for small dents that are ⁱ⁄₂  in (i.iii cm) across or less.

2. 2

   Use a plaster grid for reinforcement. Buy a sheet of plaster filigree and cutting out a small square, just big enough to cover the dent. While the drywall mud is still wet, stick the plaster grid onto the wall to comprehend and reinforce the dent.^[3]

   • Using a plaster grid is optional, but it will help reinforce your wall and forestall new damage in the future.

   Advertizing

3. 3

   Cover the plaster grid with more drywall mud. Grab your putty knife again and add more than drywall mud in a thin layer over the grid. Add just enough and so you tin't encounter the plaster grid anymore, and use your putty knife to smoothen out any lumps in the mud.^[4]

4. four

   Wait for the putty to dry out. ^[5] Drywall mud usually takes about 24 hours to dry. It's important to let the drywall mud cure completely; otherwise, your side by side steps could harm your wall even further. To speed up the drying process, point a fan at the wall overnight.^[6]

5. 5

   Sand the putty until information technology's flush with the wall. ^[7] Before you start sanding, put on an N95 mask to avert breathing in any drywall dust. Catch a sheet of 100- or 120-grit sandpaper, and so sand the drywall mud until it'south affluent with the wall. Accept your fourth dimension, and make sure the wall is really polish before y'all move on.^[8]

   • If you desire to ensure that your patch job isn't noticeable at all, yous can add some other layer of drywall mud later on the first round of sanding. Let it dry for 24 hours, and so do a concluding circular of sanding over again to smooth it all out.

6. 6

   Paint the wall to match the colour. Choice up a saucepan of pigment that matches your wall colour. Utilize a paint brush or a roller to paint the entire area then it looks seamless and polish. Once the pigment dries, you won't be able to see your patch job anymore!^[9]

   • If you aren't sure what the exact colour of your wall is, scrap off a minor sliver of paint and accept information technology to a hardware store. They'll exist able to match the paint color precisely and so you don't take to guess.
   • If your wall is textured, pick upward a can of wall texture spray and spray information technology over the patched surface area earlier you add together pigment.^[10]

Advertisement

1. 1

   Buy a drywall patch kit from the hardware shop. Most kits come up with a stencil and a drywall patch that you can cut to match the size of your verbal paring. You can discover these in the drywall section at your local hardware store, or you can search online. Some of them also come up with drywall mud and a putty knife, but if yours doesn't, be sure to pick those things upwards at the store before you start.^[xi]

   • Large dents are any dents that are wider than ⁱ⁄₂  in (1.3 cm) across.

2. 2

   Utilize the stencil to cut a hole around the dent. Grab your drywall patch stencil and utilize a pencil to draw a circle around the dent. Cut the drywall with a box cutter to remove the dent from the wall. So, pry the cut circle of drywall off of your wall and throw information technology away.^[12]

   • If your drywall patch kit didn't come with a stencil, that'southward okay! Just cut a circle around the paring with a box cutter. Y'all'll be able to modify the drywall patch if you need to.^[13]

3. three

   Spread drywall mud effectually the inside of the circle. ^[14] Take hold of a putty knife and scoop up a thick glob of drywall mud. Spread the mud all over the perimeter of the circumvolve, smoothing it out onto the wall about two in (5.1 cm) in all directions. It'southward okay if you go a niggling bit of mud on the inside of the drywall, too.^[15]

   • The drywall mud here acts equally an ballast to concord your drywall patch in place.

4. 4

   Attach the patch to the wall with more drywall mud. Catch your drywall patch and place it over the hole in the wall. Scoop up more than drywall mud, then add a thin layer over the entire drywall patch. Shine the mud out from the patch about two in (5.i cm) to actually anchor it on.^[16]

   • If you need to cutting your patch, do that with scissors commencement earlier putting information technology on the wall. Cutting a circle that's about 2 in (5.ane cm) larger than the hole in your wall.
   • To prevent the patch from falling back into the wall, avoid pressing too hard directly on the center of the circle. Focus on smoothing the drywall mud out over the edges of the patch and onto the wall effectually it.

5. 5

   Await for the area to dry out, and so sand the wall. Drywall mud commonly takes nigh 24 hours to dry. Once the area is completely dry, use 100- or 120-grit sandpaper to completely sand the unabridged area until it's smooth. Wear an N95 mask when y'all sand drywall, as the dust isn't great for your lungs.^[17]

   • Sanding the wall is the longest role of this entire process. Sanding by mitt can take up to 30 minutes.

6. 6

   Paint the wall to match the color. Pick up a gallon of paint that matches your wall color exactly. Use a pigment brush or a paint roller to cover up the patched expanse, then let it dry. If you lot're using a lighter paint color, you might need to add multiple coats.^[18]

   • If your drywall is textured, grab a can of texture spray from the hardware store and spray information technology over the patched surface area. Look for information technology to dry, then add paint on top.^[nineteen]

Advertisement

Ask a Question

200 characters left

Include your electronic mail address to become a message when this question is answered.

Submit

Ad

• Drywall dust can cause pharynx and airway irritation. E'er wear an N95 mask when sanding drywall.^[twenty]

Advertisement

Things Y'all'll Demand

• Drywall mud
• Putty pocketknife
• Plaster filigree
• 100- or 120-grit sandpaper
• N95 mask
• Paint brush or roller
• Paint

• Drywall patch kit
• Pencil
• Box cutter
• Drywall mud
• Putty knife
• 100- or 120-grit sandpaper
• N95 mask
• Paint brush or roller
• Paint

About This Article

Thanks to all authors for creating a page that has been read 9,468 times.

Did this article help you?

Source: https://www.wikihow.com/Fix-a-Dent-in-the-Wall

Share this post